Software :: Performance Manager

JBL® HiQnet Performance Manager™ is a software application designed to configure networked audio systems within performance venues such as theatre, house of worship, and corporate and other live sound events.  It dramatically reduces design time, simplifies networking and automates control interface configuration.  With considerable expert system design knowledge embedded directly into the software, Performance Manager cleverly disguises the complexity of system configuration and guides even the less-experienced user through the process so as to achieve a far more optimal result than would otherwise be possible.

It achieves this at the top-level with a comprehensive workflow paradigm, enabling the operator simply to start at the beginning by predicting speaker coverage, and then work his way through the remaining system configuration stages one step at a time.  Each workflow stage provides a dedicated interface tailored for that specific function, thereby providing a clear focus as to the goal of each operation.  The workflow finishes with an inbuilt and cohesive show monitoring and control interface.

Most significantly, all design and control is truly achieved at the system level, the more-traditional software model of individual device control still being possible, but rightly repositioned as the advanced use case.

Several innovative design concepts exist within Performance Manager:

  • Templates for flown and ground-stacked loudspeakers with pre-defined grouping information provide the starting point for configuration
  • An integrated predictive modeling tool drives the detailed configuration of the templates for both powered loudspeakers or passive loudspeaker / amplifier combinations
  • All amplifiers are added to a passive loudspeaker system and each amplifier channel is associated with the appropriate loudspeaker bandpass input in a single automated step
  • The correct loudspeaker tunings and all parameters derived from the predictive modeling are loaded into powered loudspeakers or amplifiers automatically
  • Networking is reduced to a simple drag-and-drop to connect each virtual rack or powered array in the software with the target physical rack or array on the network
  • All required control interfaces are included in the software for system calibration EQ, system tuning EQ, delay and gain eliminating the laborious task of creating customized interfaces
  • All DSP is abstracted with an automatic mapping of controls to devices, regardless of the specific system configuration, providing a consistent interface for each and every system
  • An integrated final mode converts the design workspace immediately into an interface for running the show, providing monitoring for input / output metering, load, AC and thermal levels, all monitoring driven from the representations of the loudspeakers, regardless of whether powered or amplified passive loudspeakers


New in version 1.9.2:

  • Fixed issue going to delay mode caused deadlock in some venue files


New in version 1.9.1:

  • Fixed issue that prevented running Performance Manager on Windows 10 machines or machines with .Net 4.6 installed
  • Fixed crash bugs in Line Array Calculator


New in version 1.9.0:

  • Full support for JBL VTX V20-DF
    • VTX V20 Down Fill presets are now available. For more information about the new presets please click here
  • Addressed issue where file saving would hang indefinitely in certain configurations.
  • Improved handling of input and output processing settings for generic speakers.
  • Delay Adjustment Improvements:
    • The delay values are now always displayed in ms (milliseconds).
    • The UP/DOWN delay button resolution is now set to 0.5ms
  • The Number pad improvements:
    • The display value is now always highlighted eliminating the need to press clear before entering a value
  • Improvements for the onscreen keyboard
  • Netsetter:
    • Netsetter is now integrated into the Go Online mode.
    • A Netsetter button is now available on the ribbon
  • Circuit mode improvements
    • Fixed bug where Nominal mode for V20 was not set to 3 x Boxes per circuit
    • Added nominal mode for S28/G28 when used with the 4HD amplifier
  • Master EQ Improvements:
    • Improved UI behavior to eliminate an issue were some PEQs will not show up in the user interface
  • Circuit EQ Improvements:
    • Circuit equalization is now only accessible via the Calibrate Arrays page
  • V-Rack UI improvements:
    • The scroll bar for the V-Rack mode selection box when the VRACK has been dragged into the venue space is now bigger and easier to utilize
  • Limiter UI improvements:
    • Peak limiters controls have been removed 
  • VTX V20 Passive presets:
    • Passive presets have been reworked for 2-Channel amplifiers
  • VTX S25 Ground Stack UI improvements
    • Removed the VTX V20 AF in ground stack situations
  • JBL LACII new features:
    • Improved algorithms for predicting coverage of large VTX V20 arrays in tension or compression suspension modes.
    • New calculations to improve prediction of compressed VTX V20 and V25-II-CS arrays when suspended from a single point.


New in version 1.8.6:

It is recommended that PM 1.8.4 or 1.8.5 are uninstalled, and all files which contain VTX V25-II or VTX V25-II-CS arrays must be recreated, starting from a fresh Performance Manager file. We apologize for this inconvenience, but this is necessary in order to utilize new VTX V25-II R1.3 presets.

  • Addressed an issue where JBL VTX V25-II and VTX V25-II-CS would have incorrect default input router settings
  • Crown I-Tech 4x3500HD Firmware is included – this *must* be installed in order for Performance Manager to function properly
  • In rare configurations Performance Manager would not complete saving files - this process has been optimized to address the issue


New in version 1.8.4:

  • Full support for JBL VerTec DrivePack DP-DA V5 R1 speaker presets
           - NOTE: In order to run JBL VerTec DrivePack DP-DA V5 presets please ensure that the following requirements are met:
                   - All units are updated to DPDA-1103.bnd firmware or higher
               - All units have been upgraded to current hardware specifications (refer to JBL Pro Technical Bulletin TB-053 for complete details)
                   - See the readme file for further information regarding firmware and hardware requirements
  • JBL VTX V25-II and VTX V25-II-CS
           - New V5 presets
           - Full JBL LAC II support


New in version 1.8.3:

  • Line Array Calculator / VTZ V25-CS
           - Compression suspension can be implemented on VTX V25 cabinets equipped with the optional VTX-V25-CS-K compression suspension kit and VTX-V25-PB Pull Back, VTX-V25-LH Lever Hoist accessories
           - Note: VTX V25 enclosures that are equipped with the new, optional VTX-V25-CS-K compression suspension kit are referred to as V25-CS
  • New Crown I-Tech HD firmware version
  • Updates to VTX S25 speaker presets
  • A number of other minor issues resolved
  • EQ graphs now have A/B ability (save and undo state)


New in version 1.8:

  • Support for JBL VTX V20 and S25 speakers
  • VTX V20 can be configured in both Active and Two-way Passive modes
  • VTX-V20-AF Array Frame, VTX-V20-AF-EB Extension Bar and VTX-V20-PB Pull Back accessories added to JBL Line Array Calculator
  • JBL Line Array Calculator help file included VTX V20 suspension procedure guidelines (compression and tension modes)VTX V20 presets available for Short Throw, Long Throw, Extra Long Throw (ST, LT, XLT) operating modes and the following VTX subwoofer combinations:
  • New circuiting functionality
           - 60, 80, 120 Hz sub/low processing for VTX V20 and VTX S25
           - 60, 80 Hz sub/low processing for VTX V20 and VTX G28 or S28 subwoofers
           - VTX S25 60-120 presets for use with V20 in 120 Hz mode and G28 or S28 in 60 Hz mode
           - Cardioid preset support for all of the above subwoofer models and crossover options
  • Distributed Fills now circuit inside-to-out in a more comprehensive manner. The center-fill circuits inside to out within the fill group
  • Meters that were previously rendered horizontally are now rendered vertically adding consistency and readability
  • Ground-stacks-on-end left/center/right is now more distinct and easier to configure
  • EQ graphs now have A/B ability (save and undo state)


New in version 1.7:

  • Support for JBL VTX F Series speakers
  • New circuiting functionality
           - Circuits for Ground Stacks on-end are built in an inside-to-out (on-stage-to-off) fashion
           - Center stacks mirror their circuit configuration
         - The circuit jumpers of cardioid subs are separated so non-consecutive circuiting and more economical cardioid triplets can be created
           - Crown VRACK 12000 amplifier channels are now automatically associated with sub bandpasses by using channel 1 of all three amplifiers before associating with channel 2
           - Automatic mirroring applies to more parameters: delay, bandpass gain, circuit level attenuation, limiter reduction
  • Online matching now has the option of preserving the physical device addresses and making the virtual device in Performance Manager receive the HiQnet address from the networked device
           - This option in available in the options dialog under the networking section
  • In Amplify Manually mode the associations can be made directly by dragging speaker bandpasses to amplifier channels or vice versa
           - The original method still remains
  • A fix has been implemented so that online-mode parameter values (delay, EQ, bandpass gain) are not lost when the speaker preset is changed
  • It is now possible to use circuit jumpers to mute individual circuits
  • The circuit jumper now shows the mute state for the circuit
  • Templates for Ground Stacks have been substantially changed
           - It is now possible to select any number of column or row stacks
           - Selecting an odd number of Ground Stacks on-end will create a center stack that circuits inside to out within itself
  • Templates for Distributed Fills can have any number of fills
  • In Tune System mode the delay spinners are broken out into fine (21 microseconds) and course (0.5 milliseconds) bump amounts (arrows)
  • The impedance report in Test System has been updated
  • The Array Configuration dialog now has an ‘auto’ VRACK wiring mode option – selecting this will allow Performance Manager to decide the most economical use of VRACKS and can be used instead of the Advanced tab for complex scenarios
  • Powered speakers can now have user-specified addressing

Bugs fixed

  • For powered DPDA devices the input fader was incorrectly hooked up in 1.6 and 1.6.1 versions (earlier versions were fine)
           - This could be seen in Test System mode signal generation on the main fader and applying array shading from Line Array Calculator
  • A number of muting and selection issues have been addressed
  • Muting is more explicit
  • Issues with going to Device view have been addressed
  • Rules regarding reversing subwoofers have been improved
           - The rules within Line Array Calculator remain master
  • Several issues with user-specified addressing have fixed
  • A few issues with Line Array Calculator and saving and loading files have been fixed


  • In online modes, if a dbx DriveRack 4800 goes offline and comes back online it was set to send device state which caused a mute to happen as the device state was updated
           - This behavior has been changed for the dbx DriveRack 4800 only – in this scenario Performance Manager will receive the dbx DriveRack 4800’s device state and not mute
  • Subwoofers can no longer be put into distributed fills
  • I-Tech 4x3500HD firmware has been updated
  • In Set Speaker Tunings mode, the defaults for Throw have been changed
  • Speed of muting has been optimized
  • Speed of going into Device view has been optimized


New in version 1.6:

  • New I-Tech HD 4x3500 firmware version 1042 – this is a critical update for front display operation
  • In Test System mode, the Group muting controls are available as well as the Signal Generator controls
  • Each Array / Ground Stack now has its own mute button to enable left / right testing and tuning
  • When selecting groups within the Group list, the affected speakers are highlighted in the main workspace to aid navigation
  • New Array / Ground Stack Auto Amplify button to help guide automatic amplification
  • Amplification of Arrays / Ground Stack is now possible from the Configure Array dialog
  • Delay for Arrays and Ground Stacks is now completely separate from subwoofer / EDS delay)
           - The delay product panels now show the two separate delay values
           - Note: I-Tech Series and MAi Series amplifiers do not have this ability
           - Bug fixed: delay configuration will not be corrupted when launching / closing Line Array Calculator having been online
  • New library clean-up tool
           - Custom Racks and Generic Speakers are archived in both the performance file and on disk - over time these libraries 
             can accumulate and lead to inadvertently large files
           - A new ‘Clean’ button has been added to both Add Speakers and Add Amplifiers modes to remove Custom Racks and
             Generic Speakers not in the current file from both the file itself as well as the disk library

Bugs fixed in version 1.6

  • Delay setting of zero no longer sent to amplifiers having been online and returning to Line Array Calculator
  • Cleaned up display of Racks and Arrays and minor bugs with duplicate names
  • File marked as ‘edited’ in several missing places in order to correctly prompt for saving changes
  • Fixes for bugs for user-specified amplifier addresses when adding amplifiers
  • Fix for incorrect delay values being sent to amplifiers when using mixed Arrays of 2-channel I-Tech HD Series and I-Tech HD 4x3500 amplifiers
  • Updates to amplifier / bandpass selection and muting
  • Switching the delay units radio button to ‘feet’ on a small display no longer makes the ‘meters’ and ‘seconds’ radio buttons disappear
  • Additional stability to prevent rare Line Array Calculator from hanging / crashing

Bugs fixed in version 1.6.1

  • Impedance showing 0 in Test System mode fixed
  • Angles reset after closing and re-opening Line Array Calculator fixed
  • Shelving filters displaying incorrectly in Line Array Calculator fixed
  • Occurrences of VRACKs not being matched properly fixed


New in version 1.5:

  • Support for JBL VRX Series loudspeakers
  • Support for JBL STX Series loudspeakers
  • JBL Version 5 Preset Data for VerTec Series models VT4887A / VT4887, VT4886 and VT4883
  • Custom Racks can now be designed with mixed Crown amplifier models
  • Custom Racks can now be designed to include any number of  Crown amplifiers up to a maximum of eight
  • New amplifier sleep-mode utility
  • Now possible to open a Performance Manager file and send the configuration directly to the network rather than just receive from the network
  • Support for single-channel subwoofers improved
  • Polarity and delay values set in online modes are now properly updated in the integrated JBL Line Array Calculator 


New in version 1.1:

  • Support for the Crown VRACK 4x3500 with full integration into the Performance Manager workflow
  • JBL V5 Preset Data for VerTec VT4889 (V5 R1) and VerTec VT4888 (V5 R1)
         - Short Throw (ST) and Long Throw (LT) preset support for VT4888 and VT4889, with HF shelving characteristics that are consistent with VTX V25
           - Sub / low preset (X, 60, 80) support for VT4888 and VTX G28, S28 subwoofers
           - Cardioid preset (X, 60, 80) support for VT4882, VT4880, VT4880A subwoofers
           - Cardioid preset (X, 60, 80) support for VT4880 and VTX S28
           - Cardioid preset (X, 60, 80) support for VT4880A and VTX S28
           - Revised limiter thresholds
           - The VTX V25 R1.1 release for Crown Audio IT12000HD includes minor changes to subwoofer model limiter thresholds
  • JBL V5 Preset Data VTX V25 (V5 R 1.1) release for Crown Audio I-T12000 HD
           - Minor changes to subwoofer model limiter thresholds
  • JBL V5 Preset Data VTX V25 (V5 R 1.2) release for Crown Audio I-T4x3500 HD
           - Minor changes to subwoofer model limiter thresholds and introduces extra long throw (XLT) support
  • Network sharing is now always on
  • Significant bug fixes:
           - Amplifying user-defined speaker with factory-defined speaker is now possible in same amplifier
           - Occasional fail on export of user-defined speakers fixed
           - Occasional crash on entering “Edit Groups” mode fixed
           - Gain reduction meter now shows maximum reduction


Performance Manager 1.8 supported devices:

  • JBL VTX Series V25, V20, S25, G28 and S28 models
  • JBL VTX F Series
  • JBL powered VerTec Series [with DP-DA installed]
  • JBL passive VerTec Series
  • Crown I-Tech HD Series
  • Crown Macro-Tech i Series
  • Crown VRACK 12000
  • Crown VRACK 4x3500
  • Crown I-Tech Series [discontinued]
  • dbx DriveRack® 4800 / 4820
HiQnet Performance Manager™ 1.9.2 FULL installer


The above installer requires a license key to run.
Click to email and request a license key...

The above installer requires that the Microsoft .NET Framework 4 or newer be installed on the host computer. If the Microsoft .NET Framework 4 is not already installed:

  • EITHER an active internet connection must be available during the installation procedure
  • OR the Microsoft .NET Framework 4 installer can be downloaded and installed prior to Performance Manager installation
  • Click here to download older versions of Performance Manager.

    System Requirements

    Supported Operating Systems:

    • 32 & 64-bit versions of Windows Vista, Windows 7
    • Note - Performance Manager is not supported in Windows 8 at this time

    Minimum Performance Guidelines:

    • CPU: 32 bit dual core @ 2.0GHz or better
    • RAM: 2GB

    Optimal Performance Guidelines:

    • CPU: 64 bit dual core @ 2.50 GHz or better.
    • RAM: 4GB or more
    • OS: 64-bit Windows Vista or Windows 7


    * All three levels require a hard disk with at least 400MB free space.